Chongqing TOP Oil Purifier Co., Ltd. is one of the most reliable manufacturers and suppliers of steam turbine oil purifier in China, also supports customized service. Please feel free to buy advanced steam turbine oil purifier made in China here from our factory.
Description
The TY-A Steam Turbine Oil Purifier runs a PLC-controlled vacuum dehydration and 1µm absolute filtration process to remove water, gas and fine particles from turbine lubricants, delivering residual moisture ≤50 ppm and gas content ≤0.1% without constant operator attendance. It can be used for offline batch treatment or connected for inline oil conditioning while turbine generators remain in service.
Technical Parameters
|
Item |
Unit |
TY-A -10 |
TY-A -20 |
TY-A -30 |
TY-A -50 |
TY-A -100 |
TY-A -150 |
TY-A -200 |
TY-A -250 |
TY-A -300 |
|
|
Flow Rate |
L/min |
600 |
1200 |
1800 |
3000 |
6000 |
9000 |
12000 |
15000 |
18000 |
|
|
Flow Rate |
L/H |
600 |
1200 |
1800 |
3000 |
6000 |
9000 |
12000 |
15000 |
18000 |
|
|
Working Vacuum |
Mpa |
-0.06 ~- 0.098 |
|||||||||
|
Working Pressure |
Mpa |
≤0.3 |
|||||||||
|
Temperature Range |
℃ |
0~100 |
|||||||||
|
Working Oil Temperature |
℃ |
45~65 |
|||||||||
|
Power Supply |
380V/50HZ/3Ph 5 wire (Customizable) |
||||||||||
|
Continuous Working Time |
H |
≥150 |
|||||||||
|
Working Noise |
dB(A) |
≤65 |
≤68 |
≤68 |
≤70 |
≤70 |
≤75 |
≤75 |
≤78 |
≤80 |
|
|
Electric Heating Power |
kW |
15 |
18 |
24 |
36 |
60 |
72 |
120 |
150 |
180 |
|
|
Total Electric Power |
kW |
17 |
20 |
26 |
39 |
65 |
79 |
128 |
180 |
192 |
|
|
Inlet/Outlet |
mm |
Ф25 |
Ф25 |
Ф25 |
Ф32 |
Ф42 |
Ф45 |
Ф50 |
Ф60 |
Ф63 |
|
|
Weight |
kg |
350 |
400 |
450 |
500 |
900 |
1300 |
1500 |
1800 |
2000 |
|
|
Size |
L |
mm |
1350 |
1400 |
1450 |
1500 |
1700 |
1800 |
2000 |
2100 |
2400 |
|
W |
mm |
950 |
1000 |
1050 |
1100 |
1150 |
1250 |
1400 |
1450 |
1550 |
|
|
H |
mm |
1650 |
1700 |
1750 |
1800 |
1800 |
2000 |
2200 |
2300 |
2400 |
|
|
Index After Filtration |
Moisture Content |
PPM |
≤50 |
||||||||
|
Gas Content |
% |
0.1 |
|||||||||
|
Impurity Size |
μm |
≤1 (Customizable) |
|||||||||
Features
- Aged transformer oil typically carries dissolved water, acids and oxidation sludge that pull down the breakdown voltage and push the dissipation factor beyond acceptable limits. Regeneration columns packed with activated alumina strip out these acidic compounds and oxidation by‑products, restoring dielectric strength and bringing the oil back within serviceable values.
- Deep vacuum dehydration reduces dissolved moisture to 10 ppm or below, which raises the breakdown voltage enough for reliable insulation at transmission and distribution voltages.
- An integrated degassing stage removes dissolved air and other gases to 0.1% or lower, preventing gas bubbles from forming under high electrical stress the kind that lead to partial discharge and eventual insulation failure.
- Multi-stage fine filtration traps particulate matter down to 1 µm absolute, keeping the oil clean enough for power transformers, instrument transformers and circuit breakers.
- A PLC-based control system manages the full regeneration cycle without operator attendance and logs process data for maintenance planning and compliance records.
FAQ
Q: Can it regenerate oil with very high acid value?
A: The regeneration filter can reduce acid value to a certain extent. If oil is severely oxidized with excessive acid value and plenty of asphalt‑like sediments, physical purification alone cannot restore oil completely. It is advised to replace part of new oil.
Q: What ambient conditions are required for operation?
A: Working environment temperature: 5‑45℃; avoid heavy dust, rain and corrosive gas. Indoor installation is preferred; outdoor usage needs rain‑proof shelter.
Q: Troubleshooting: Low vacuum degree, how to check?
A: 1. Check all pipeline joints and door covers for air leakage.
2. Inspect vacuum pump oil quality, replace if deteriorated.
3. Check whether inlet oil flow is too large.
4. Confirm sealing rubber rings are intact.